One of the popular trends in eye wear these days are known as the clip on flip up sunglasses because these things can actually replace actual sunglasses with the same quality. Now one many do not know is that it is actually possible to make this kind of accessory instead of going out to a store and buying one. Now if one is interested in trying to create one of these things, then try following some of these steps.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
After making the wire straight, take a pair of scissors and cut the wire in the middle until it becomes two. From there, one must now place one wire into the hole at the sides of the glasses. After that, he should take the other piece of wire and do the exact same thing.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
The next thing to do would be to take the two ends of the wiring and try to tie them together in the middle. Take note that the wire has to be attached to the frame of the glasses so that it cannot be seen. When the two ends have been brought to the middle, then try to tie them together.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So basically, that is an easy way on how to make clip on flip up sunglasses. The great thing about making this at home is that it is cheaper than buying one outside. Also, it is more practical than an actual pair of sunglasses because it is smaller and it will not get spoiled easily.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
After making the wire straight, take a pair of scissors and cut the wire in the middle until it becomes two. From there, one must now place one wire into the hole at the sides of the glasses. After that, he should take the other piece of wire and do the exact same thing.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
The next thing to do would be to take the two ends of the wiring and try to tie them together in the middle. Take note that the wire has to be attached to the frame of the glasses so that it cannot be seen. When the two ends have been brought to the middle, then try to tie them together.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So basically, that is an easy way on how to make clip on flip up sunglasses. The great thing about making this at home is that it is cheaper than buying one outside. Also, it is more practical than an actual pair of sunglasses because it is smaller and it will not get spoiled easily.
About the Author:
You can visit the website www.brimzsports.com for more helpful information about How To Make Clip On Flip Up Sunglasses
#end